Inline taps or ball valves are a very useful accessory for the Autopot when having 4 for more Autopot units. They can be added to the end of a layout when you are using pipe  You can open the tap and allow the lines to be flushed, removing a sediment or lime scale build-up that might occur over time. This will only take a couple of minutes and only needs to be done every couple of weeks.
Chokes / valves / inline taps are used to restrict the volume of water passing through a pipe. They are ideal for things like NFT systems, where the flow-rate might need to be adjusted to fit specifications (1 – 2 liters per minute through a channel). They also solve the problem of plants that require differing amount of water at different times of the year.
It is important to note that these are chokes and may not necessarily shut off completely.
The AirDome is the perfect accessory to gardeners of all abilities. It has been designed to increase the amount of air around the root zone in plant pots.
Airdome inside pot
If you are lucky enough to have power in your greenhouse or tunnel this little addition can increase yields by up to 130%. It is very simple to use once assembled, which will take less than 30 seconds. The AirDome is placed at the bottom of the pot, covered with compost and then connected to an air pump. Oxygen is then supplied directly to the plantsâ root zone, improving crop development and ensuring maximum growth.
It is very easy to use. The AirDome is placed at the bottom of the pot, covered with the substrate of choice and then connected to an air pump.
To maximise the effectiveness of the AirDome use a fluffy mix such as a mixture of 50% good Coco Peat and 50% Perlite.
Provide the plants with additional oxygen to boost growth significantly and increase yields.
To increase levels of oxygen for smaller plant at times when the medium seems to stay wet.
With all growing conditions being correct the Air Dome has been proven to increase yields by up to 130%
The AirDome should only be switched on during the daylight periods. Always ensure that warm air is blown in and around the root zone. Temperatures between 18 and 22 degrees are ideal. Temperature below and above 5 degrees and 30 degrees will potentially damage the roots.
Raise your air pump higher than the AirDome(s) to prevent water from siphoning back when the pump is off or use a non-return valve.
Use a timer to turn the pump on and off when the air temperature is warm and before it gets too cool.
Many AirDomes can be linked together using 5mm connections, or for larger AirDome setups, use 12mm pipe as the supply line, reducing the pipe at each AirDome point with the AutoPot 12mm to5mm Cross Connectors.
T Connector 12mm to 5mm will be needed when extending AutoPot Units.
These connectors are perfect for reducing 12mm pipe down to 5mm pipe, when using large systems. They are inserted in-line at the point where an AQUAvalve or aquaPot is positioned. They provide a water tight connection unlike many other types of reduction fittings. They work in exactly the same way as the Cross Connector 12mm to 5mm but this fitting (T Connector 12mm to 5mm) has one connection for 5mm pipe whereas the cross connector provides two connections for 5mm pipe.
The wide range of AutoPot fittings cater for every gardening scenario and need. Whether waterbutt connection, extending your system, pipework or filters, we have a fitting for every alteration or horticultural situation. Our fitting range ensures maximum efficiency and simple success with your irrigation system. AutoPot watering systems are modular, so can be infinitely extended using our fittings you can simply just add more pots as you require them.
High quality parts for extending the AutoPot range, or for use in any homemade irrigation system.
AutoPot are specialists in self-watering systems, with emphasis being strongly placed on efficiency and preservation. AutoPot delivers products that are considered the most environmentally friendly watering systems in the world to both domestic, hydroponic and commercial markets. Our systems ensure this claim as the plant uses everything that is supplied to it; there is no loss of water, run-off or leakage!
Cross Connector 12mm to 5mm will be needed when extending AutoPot Units.
These connectors are perfect for reducing 12mm pipe down to 5mm pipe, when using large systems. They are inserted in-line at the point where an AQUAvalve or aquaPot is positioned. They provide a water tight connection unlike many other types of reduction fittings. The Cross Connector 12mm to 5mm has two connections for 5mm pipe.
The wide range of AutoPot fittings cater for every gardening scenario and need. Whether waterbutt connection, extending your system, pipework or filters, we have a fitting for every alteration or horticultural situation. Our fitting range ensures maximum efficiency and simple success with your irrigation system. AutoPot watering systems are modular, so can be infinitely extended using our fittings you can simply just add more pots as you require them.
High quality parts for extending the AutoPot range, or for use in any homemade irrigation system.
AutoPot are specialists in self-watering systems, with emphasis being strongly placed on efficiency and preservation. AutoPot delivers products that are considered the most environmentally friendly watering systems in the world to both domestic, hydroponic and commercial markets. Our systems ensure this claim as the plant uses everything that is supplied to it; there is no loss of water, run-off or leakage!
Aluminium Tape is highly reflective. Aluminium Tape is very useful in that once you stick it down it will not fall off  when exposed to moisture rich environments.
50 m roll, 5 cm wide.
Aluminium tape is particularly effective for joining or sticking down Mylar or Sisalation or joining ducting pieces together.
Siliconised release backing paper needs to be peeled off before use.
Conformable tape resists flame, moisture, weather, UV degradation and many chemicals, making it ideal for a variety of applications
Heat and light reflective tape protects, insulates and enhances lighting efficiency
Withstands a wide temperature range
Thermally conductive tape helps dissipate heat and improves heating and cooling efficiency
Transparent acrylic adhesive combined with the rugged, durable backing provides long service life both indoors and out.
Made from Neem oil, Biogrow Bioneem is a natural botanical insecticide.
It is a natural insect repellent, causes appetite loss in sucking insects, ingestion by pests will cause a disruption of their hormone cycle and negatively affects their breeding ability. Think of it as “anti-Viagra” for pests.
Pests – whitefly, mites, aphids, thrips, leafminer, various beetles and fruitfly.
The key insecticidal ingredient found in Biogrow Bioneem tree is azadirachtin, a naturally occurring substance that belongs to an organic molecule class called tetranortriterpenoids. It is structurally similar to insect hormones called âecdysonesâ which control the process of metamorphosis as the insects pass from larva to pupa to adult. Metamorphosis requires the careful synchrony of many hormones and other physiological changes to be successful, and azadirachtin is an âecdysone blockerâ. It blocks the insects production and release of these vital hormones. Insects then will not moult, thus breaking their life cycle.
Azadirachtin also serves as a feeding deterrent for some insects. Depending on the stage of life-cycle, insect death may not occur for several days. However, upon ingestion of minute quantities, insects become quiescent and stop feeding. Residual insecticidal activity is evident for up to seven days or longer, depending on insects and application rate.
Composition:
PLEASE NOTE:
5lt and 25lt VOLUME IS TWICE AS STRONG AS THE 250ml and 500ml VOLUMES!
Product may turn opaque and thicken up in colder conditions – this is normal.
250ml & 500ml: 1500ppm azadirachtin
5lt: 3000ppm azadirachtin
Application rate (Varies, depending on the growth stage of plant and insect pressure):
250ml & 500ml: Between 3 ml â 5 ml per 1 L water
5lt and 25lt: Between 1.5 ml â 2.5 ml per 1 L water
Insect Control
Biogrow’s aim is to control insect populations to a level where minimal damage is caused to the crop and the beneficial insects have a supply of food. The closer we get to creating this balance, the healthier our environment will be.
During dormancy (winter) plants can be sprayed with Pyrol for the control of scale insects and the overwintering mealy bug.
During the growing season alternate at 10-14 day intervals between sprays of Bioneem and Pyrol. Under high insect infestation and increased plant damage spray Pyrol at shorter intervals, every 7 days, in order to suppress the population of insects to a minimal level. Then continue with maintenance program.
Make a fresh batch each time you spray.
Application rate varies between 3 ml â 5 ml per 1 L water, depending on the growth stage of plant and insect pressure.
An E40 Lamp Holder device which mechanically supports a lamp for the purposes of making electrical contact with the lamp.
E40 is the standard fitting for all our HPS, MH and CFL bulbs
DIY – Build your own light system
E40 Lamp Holder fitting is commonly used for horticultural lamps. Useful for growers who are creating their own lighting fixtures or those who have no need for a reflector. The holder is suitable for use with all CFLs, MH and HPS lamps.
Please note: Our E40 socket CFL lights (85 Watt and 140 Watt) emit a colour temperature of 6400K ( “Cool Blue” ), ideal for vegetative growth. Our 2700K (“Warm White”) CFL lights (200 Watt), also E40 light fitting.
We suggest starting off with 140 Watt Cool Blue E40 CFL’s if you are planning to switch colour temperatures during the later stages of your grow cycle.
Wurmbosch Worm Castings are a rich, all-natural source of organic matter with lots of nutrients and moisture-holding capabilities.
Vermicast, also called worm castings, worm humus or worm manure, is the end-product of the breakdown of organic matter by an earthworm. These castings have been shown to contain reduced levels of contaminants and a higher saturation of nutrients than do organic materials before vermicomposting.
Earthworm castings are known to have an extraordinary effects on plant life. Worm Castings improve the soil structure and increase fertility making them the most enriching soil conditioner available.
Widely & successfully used for propagation and all stages of transplants and a 10% to soil mixes come highly recommended.
Can also be effectively used to make teas, for foliar application to green up leaves and to help keep insects at bay, mainly during vegetative stages.
The product must be kept closed to maintain moisture levels for bacteria to stay alive until ready for use.
Recommended  Usage:
As fertilizer or top dressing, scatter 1 cm on indoor plants or 2 cm on outdoor plants every 2-3 months.
For planting seedlings, put 1 heaped Tbs (40-50ml) into prepared hole.
Add 1/3 worm castings to soil to make potting soil.
7.0 pH Calibrating Solution is to be used with the Digital pH Pen
Suitable for all makes and models of pH pens and meters. pH 7.0 Calibration Solution is easy to use! Just dip your electrode into a small amount of the buffer and adjust the meter to read 7.0. Do not reuse solution.
7.0 pH Calibrating Solution is used to calibrate your pH meter to ensure it maintains itâs accuracy. It is made under strict industry standards in order to give you a solution that is highly accurate and of good quality that will last up to 1 year once opened.
Made from high quality salts and de-ionized water, they are made to be accurate up to +/- 0.01 pH and will be your best friend when it comes to keeping your meters consistently accurate.
Tip: The more you use your pH Pen or Meter, the more often do you need to calibrate.
Important tips which will help you calibrate the pH meter accurately:
Follow the Manual
The calibration process will change depending on the meter being used. Always read the manual when you receive the pH meter in order to understand your specific meter and perform calibration correctly.
Use the Right pH Buffers
When you perform a pH meter calibration, you must ensure that appropriate buffers are being used. If you want to measure any substance that has a pH of 9 but you calibrate your meter to a pH of 7, you will certainly not get an accurate measurement. The pH measurements are the most accurate only when the calibration points bracket the measurement.
Calibrate Often
It is recommended that you calibrate the pH meter every time you need to perform a new set of measurements to get accurate results. It can even help you identify a problem with electrodes. Ideally, you must calibrate your meter when:
â You use it for the first time
â Use it after it has been stored for a long time
â Before performing a new set of measurements
Use Best Practices
Some of the suggested best practices are as follows:
â Ensuring that the glass bulb of the pH electrode is well hydrated before you perform the calibration. Calibrating a dry pH electrode will require frequent calibrations.
â Using sufficient amount of pH buffer to fully submerge the pH bulb and the reference junction, which is usually a small ceramic frit on the side of the probe. Always use fresh buffer solution for calibration as old or used buffer solutions may be contaminated.
â Stir the solution during the process of pH meter calibration and measurement, and wait for the electrode reading to stabilize before noting each calibration point.
Electrode Care
You must handle the electrodes with extreme care as they are responsible for taking the measurements. Never store them in distilled or deionized water as it damages or dehydrates the sensing glass of the pH electrode and depletes reference electrolyte. Rather, store the electrodes in proper storage solution as it ensures that your electrode provides stable and highly responsive readings due to a well-hydrated bulb.
Jiffy 7 Pellets 41mm are made from Sphagnumpeat from specially selected peat bogs. Lime and a special fertilizer with a low ammonium content are added to the peat in order to stimulate growth. The pellets have a pH of approximately 5.3 and are wrapped in a thin, biodegradable net.
Jiffys are a popular ready to use media and are perfect for seed germination and also for rooting plant cuttings or clones.
The compressed pallets are approx. 41mm W x 42mm H when fully expanded. When exposed to water the Jiffy expands and the hydrated media is held within a degradable net. A small indent is provided on top of the disc to place the seed into once the disc has expanded.
Because the Jiffys have an outer netting to hold the media inside, they can be self-standing or growers can place them inside seedling trays for additional support. ( Handy when rooting cuttings )
Once a good root system has developed throughout the media, they can be directly planted into an NFT system or a larger plastic or fabric pot or even a rockwool slab.
Jiffy 7 Pellets 41mm are also very popular for soil growers and can be directly planted into the soil when the seedling is established.
Jiffy 7s are manufactured from sphagnum peat (and Coir fibers) harvested from carefully selected bogs which are subject to stringent internal and governmental controls to ensure minimal environmental impact. Peat is only taken from sources where the re-generation rate is greater than the harvest rate and the local ecology will not be adversely affected.
The AQUAvalve cover if used in conjunction with the AQUAvalve allows the grower to create their own basic but very effective hobby system if used correctly.
All that is needed is a flat tray of any shape or size. The user then simply places the AQUAvalve in the tray & places the AQUAvalve cover over the top of it. A small weight of any kind needs to be placed on the AQUAvalve cover to weigh it down, a small pot of compost or a stone will suffice, ensuring that you do not cover the small breather hole on the top of the AQUAvalve cover. Once in place simply connect the AQUAvalve to a tank, using a length of 6mm pipe and a filter. Although a very basic method, this home made system following the guidelines above can be very effective.
When making your own hobby systems please ensure that the tray is as level as possible and that the pot size is not less than 5 ltrs. If you use small pots you will risk the chance of drowning the plants.
A small plant in a small pot will not appreciate being sat in deep water as the root system will not be able to breath, this obviously does not apply to bog plants or carnivorous plants. If you intend to grow carnivorous plants using this method please ensure you only use rain water.
The Lumii Black 600w Electronic Kit is supplied with the Lumii BLACK 600w Electronic Ballast, Lumii Black 600w Dual Spectrum lamp and the Lumii Black reflector.
The ballast features both a dim and a boost functions enabling you to control the light output from your lamp to your plants. It can be dimmed down to both 250w and 400w and also has a âsuper-lumensâ boost option (600w+Boost) which is on average a 10% increase in output.
This Lumii Black Lamp is a 600w Dual Spectrum HPS Lamp. It is an essential for stimulating enhanced flowering as it gives out 88,000 Lumens and lasts for up to 18,000 hours.
A Dutch Barn-Styled, Euro Reflector the LUMii Black Reflector does exactly what it should. Complete with lamp holder, mounting holes to attach rope ratchets to, and a 4m length of kettle-plug cord.
We recommend using a 600w lamp for 600w dimmer settings, a 400w lamp for 400w dimmer settings and a 250w lamp for 250w dimmer settings.
Never boost a lower wattage lamp to a higher lamp setting.
We use cookies to ensure that we give you the best experience on our website. If you continue to use this site we will assume that you are happy with it. Privacy policyOk
